![]() Keep in mind I am not a mechanic, u are responsible for your own actions. U can put it in park as soon as the diff cover is in place. Your good to go!īecareful as the truck is in neutral, make sure the wheels are blocked in the front. Put them in a bit better than finger tight and wait 1hr to fully tighten with a rachet.Īdd 75w90 synthetic (2 litres) Put the drums then wheels back on. Improve your workshop with the best bolt extractors for cars and trucks when you shop AutoZone. But the cover back on, but in a couple bolts at like 11 oclock and 6 and 7 just to hold it in place while u then insert the remaining bolts. Use rtv gasket maker around the diff housing (of course u got the old rtv off as much as possible off both the diff housing and the cover) include the bolt holes taking care to not fill the holes. Return the pin and put the small bolt in. With the c rings back pull the shafts one at a time outward so the rings stay in place. Essential for most GM and Ford Mechanics and Weekend Mechanics. For Broken Differential Pinion Shaft Lock Bolts In most GM and Ford Integral (WER type) Differentials. DPK-01 Differential Pinion Shaft Lock Bolt Extractor Kit. Now remove the pin again so to move the shafts and return the c ring to the shaft. DPK-01 Differential Pinion Shaft Lock Bolt Extractor Kit. Be gentle, don’t knock the gears too hard. Be careful!Ĭoat the lip of the seal with axle lubricant for protection prior to installing the axle shaft. Install a new axle seal using a block of wood and rubber mallet seating the lip. I used a ruler and measured all the way round matching the other side as the bearing wasn’t removed yet. Install the axle shaft bearing using the old bearing and a block of wood and a heavy hammer. I used a dremel and smoothed a nice sharp ridge Remove any old sealer or burrs from the tube. Remove axle shaft seal from the end of the axle tube with a small pry bar, Remove the axle shaft bearing from the axle tube with Bearing Removal Tool / Slap Hammer with bearing attachment. Use care to prevent damage to axle shaft bearing and seal in the axle tube. I would return the pin to keep the gears in place. Once you pull the old bearing/seal out, lube the outside of the new bearing and gently start it in the tube. You will need a slide hammer and an axle bearing puller attachment. It will let the axle shaft woble just enough to stretch out the seal and cause a leak. Product Line: John Dow Differential Pinion Shaft Lock Bolt Extractor Kits. This enable you to push the axle shaft in and remove the c ring on either side. Most axle seals fail as a result of the bearing going out. Deluxe Differential Pinion Shaft Lock Nut Bolt Extractor Kit. Remove lock screw and pinion mate shaft from differential case. This item: Dorman 81048 Differential Shaft Lock Bolt Compatible with Select Models. Rotate differential case so pinion mate shaft lock screw is accessible. Remove Rear diff bolts using a ½ inch socket, leave the top 2 bolts so the cover doesn’t hit the container catching the oil. Using a rubber mallet, hit around drum and from the back at the lip. This kind of puller puts all the force on the outer race and works 234324342% better than the jaw type.Place transmission in neutral. Tighten the nut keeps the puller in the correct position and the bearing came right out. I clicked on this link Same tools I used, same driver etc Just a better shot of the puller above. Auto zone has a nice aluminum set, much better vs using a socket. Also don't forget to get the bearing driver mandrels. It took only 3 pulls to get the bearing out the last time i did it. Pay a deposit when you pick up the tool, and we will refund you when its. The correct tool looks like this there were a few lengths to choose from in the kit. Includes: Forcing screw with shaft protector and pulley removal plate. That took ALOT of force and pulled the roller bearings out of one of the bearings. I used a 3 jaw puller the first time pulling the factory installed bearings. The key was to have the correct length puller, and one that was not already damaged. I had gotten a brand new set of blind bearing pullers along with the slide hammer from Auto Zone.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |